Water expands as it freezes. In a closed pipe, the ice plug pushes pressure into the water trapped between the ice and the nearest closed tap or valve, and the pipe splits there. That is why the leak often shows up away from the coldest spot, and often only once the ice thaws and water starts moving again.
The City of Waterloo warns that cold weather can freeze water lines and meters, causing leaks and costly repairs. Its advice is short: keep the home warm, let water run occasionally, and shut off and drain outdoor water lines and taps before winter. This guide explains how to do each of those in a Waterloo house, what to do when a line freezes or splits anyway, and how to get the air out of the pipes afterwards.
Where pipes freeze depends on when the house was built
The freezing points in a house are the places where a water line sits near cold air: the outside walls, the rim joist where the floor meets the foundation, crawl spaces, unheated garages, and the line to each outdoor tap. What changes from house to house is the pipe and how it fails.
- Pre-war houses (MacGregor-Albert, Mary Allen, Menno Euclid): houses of this age typically started with galvanized steel or lead water pipe. Galvanized pipe that is already corroded inside has thinner walls and less room for ice, so it splits sooner. Lead pipe is soft and deforms. The original shut-off valves are often old gate valves that may not close fully. Find out whether yours works before you need it.
- Post-war houses (Veterans' Green, Colonial Acres): these typically have copper water pipe. Copper splits along its length when it freezes, usually as a thin seam that sprays once the pipe thaws.
- Newer houses (Laurelwood, Clair Hills, Vista Hills): these typically have copper or PEX water pipe. PEX tolerates ice better than copper, but the brass or plastic fittings that join it do not, and a frozen fitting can let go. These houses also drain their foundations to a sump pump. The pump's discharge line runs outside, and if it holds water it can freeze shut. Then the pump runs against a blocked line. Check that the outdoor end of the discharge is clear and sloped to drain. See sump pumps.
If you are not sure what pipe is in your house, look at the line where it comes through the basement wall before the meter. In houses built before the 1950s, the City says lead was sometimes used to connect homes to the watermain. Our guide on Waterloo tap water and lead covers how to identify and test for it.
Drain the outdoor taps before the first hard frost
An outdoor tap is a pipe that runs from a heated basement through the wall to the outside. If water sits in it over the winter, it freezes. The fix is to close it off from the inside and empty it.
- Find the indoor shut-off valve for each outdoor tap. It is usually on the basement ceiling or wall, on the line heading to that outside wall.
- Close the indoor valve fully.
- Disconnect the garden hose. A hose left attached holds water in the tap body, even on a frost-free style tap, and that trapped water is what splits it.
- Open the outdoor tap and leave it open so the line between the valve and the tap can drain.
- If the indoor valve has a small drain cap on its side, open it over a bucket to let out the last of the water, then close it again.
- Leave the outdoor tap open for the winter.
If water keeps coming from the outdoor tap after the indoor valve is closed, the valve is not sealing and needs replacing before the frost.
Keep the indoor lines above freezing
Most indoor freezes happen in a cold snap, in a pipe that was fine in every other winter.
- Keep the heat on throughout the house, including when you are away. Do not turn the thermostat down hard for a trip.
- Open the cabinet doors under sinks on outside walls so room air reaches the pipes.
- Close and seal basement windows and vents near water lines, and keep the garage door shut if pipes run through the garage.
- In a deep cold spell, let a tap on an exposed line run occasionally, as the City advises. Moving water is much harder to freeze, and an open tap gives pressure somewhere to go.
- Insulate exposed lines at the rim joist and in crawl spaces with pipe sleeves, and seal drafts where pipes pass through the outside wall.
- Keep the water meter area warm and free of drafts. The City names meters along with water lines as things that freeze.
If a pipe freezes in the same place every winter, the line is in the wrong place. Moving it away from the outside wall is a change to the plumbing. Under the Building Code Act, 1992, installing, extending or materially altering plumbing generally needs a building permit. The City's building department confirms whether a particular job does.
How to thaw a frozen pipe
A tap that gives a trickle or nothing on a cold morning, while other taps run normally, points to a frozen section on that line.
- Open the tap the line feeds, so meltwater and pressure have somewhere to go.
- Warm the pipe starting at the tap end and work back towards the cold spot. Use a hair dryer, a heating pad or warm towels.
- Never use an open flame, a propane torch or a heat gun on a pipe. Flame can set fire to the framing, and overheating a frozen section can burst it.
- Keep a hand on the main shut-off while you work. A pipe that has split will start leaking as soon as the ice gives way.
If you cannot reach the frozen section, or no water reaches any tap in the house, the freeze may be at the meter or at the service line where it comes in. Leave that one to a plumber.
How to shut off the water in an emergency
When a pipe splits, the damage depends on how quickly the main valve is closed. Find it now, before you have a leak.
- The main shut-off is usually where the water service comes through the foundation wall, often in the front of the basement, next to the meter.
- Many houses have a valve on each side of the meter. Close the one on the house side, the one after the meter.
- A round wheel handle is a gate valve. Turn it clockwise until it stops. Do not force an old one that won't move, because the stem can snap.
- A lever handle is a ball valve. Turn it a quarter turn so the lever sits across the pipe.
- Once the main is closed, open the lowest cold tap in the house to drain what is left in the lines and take pressure off the leak.
- If water is near a light fitting, an outlet or the electrical panel, turn off the breaker for that area and stay out of the water.
- For a leak at the water heater, close the cold supply valve on top of the tank as well as the main.
If the main valve will not close, or the leak is on the street side of the meter, there is nothing more you can shut on your side. That is an emergency plumber call.
How to get the air out of the lines afterwards
When a line has been drained or repaired, air fills the pipes. When you turn the water back on, it comes out as spitting taps, banging pipes and a cloudy first glass. Clear it in order:
- Close the taps you opened to drain the system, except one on the lowest floor.
- Open the main valve slowly, about a quarter of the way, and let the lines fill.
- Working from the lowest floor up and from the tap nearest the main to the farthest, open each tap, cold and then hot. Leave it running until the flow is steady with no sputtering.
- Flush each toilet once, and run the outdoor taps only if they were not drained for winter.
- Open the main fully.
- If the aerators sputter or the flow is weak afterwards, unscrew them and rinse out the scale and grit that the surge knocked loose. Waterloo's water is hard, and that loose scale is common.
If the water heater was drained, refill the tank with a hot tap open until water runs steadily. Only then turn the heater back on.
If a pipe has split, the main won't close, or the water won't run once it is back on, see plumbing repairs.