Skip to content
Waterloo Plumbing and Drain

Guides

Gas water heaters in Ontario: installation and hard water

Who may install and service a gas water heater under Ontario Regulation 212/01, what decides the cost, and how Waterloo's hard groundwater scales tanks and tankless units before their time.

7 min read Updated November 17, 2026.

A gas water heater in Waterloo has to meet two conditions. A provincial regulation decides who may connect it to gas, and the hardness of the local water decides how fast scale builds up inside it. Between them, they shape what an installation involves, what maintenance it needs and how long the heater lasts.

Gas appliance work in Ontario is a regulated trade

Under Ontario Regulation 212/01 (Gaseous Fuels), fuel-fired appliances such as gas water heaters must be installed and serviced by a contractor registered with the Technical Standards and Safety Authority, using qualified gas technicians. The rule covers the gas supply connection, the venting, the burner and the controls. It also covers servicing: relighting a pilot, replacing a thermocouple or flame sensor, or adjusting the gas valve.

The water side of the job is plumbing. Plumbing is a compulsory trade in Ontario. Anyone doing it must hold a Certificate of Qualification, a provisional certificate or a registered apprenticeship training agreement, and must appear on the Skilled Trades Ontario Public Register. You can search that register by name before the work starts.

Permits are separate from trade qualifications. Under the Building Code Act, 1992, installing, extending or materially altering plumbing generally needs a building permit. The City of Waterloo's building department decides whether a particular water heater job needs one, so ask before the old tank comes out, especially if the job changes the type of heater, the piping or the venting.

At Waterloo Plumbing and Drain, the job is split along those same lines. Gas work is performed by TSSA-certified gas technicians. Work is performed by licensed plumbers (306A Certificate of Qualification).

What decides the cost of an installation

Installation prices vary because the work around the tank varies. These items make one job larger than another:

  • Like-for-like or a change of type. A tank replaced by a tank of the same type and venting usually reuses the existing gas line, vent route and piping. Switching from a tank to a tankless unit often needs a larger gas supply, a new vent through the wall and a condensate drain.
  • Venting. A conventional heater vents by natural draft up a chimney. Power-vented and direct-vent units run plastic vent pipe out through a wall. In older houses, including the pre-war houses of MacGregor-Albert and Mary Allen, a water heater may still vent into a masonry chimney. That chimney has to be assessed for the new appliance rather than assumed to be suitable.
  • Gas piping. The length and diameter of the line from the meter determine whether it can supply the new heater's input rating.
  • Temperature control. Article 7.2.10.7 of Ontario's Building Code limits the water reaching a shower head or bathtub to 49 degrees Celsius. Meeting that limit can mean lowering the tank setting or adding a temperature-limiting mixing valve. Either way, the temperature should be measured at the tub after installation.
  • Expansion and relief. If the water supply has a check valve or backflow preventer, heated water has nowhere to expand, so a thermal expansion tank may be needed. The temperature and pressure relief valve needs a discharge pipe that ends near the floor.
  • Permit, removal and access. The permit, getting the old tank out and the space the new one goes into all add to the job.

Ask for a written price that lists these items separately. Two prices are comparable only when they cover the same venting, the same gas work and the same temperature control.

Hard water is the main reason heaters fail early

The Region of Waterloo supplies the City with treated water drawn from groundwater and the Grand River. The Region describes the groundwater as hard. The water softener guide it runs with the City of Guelph maps Waterloo's hardness in zones ranging from 17 to 20 grains per gallon up to 32 to 36. It lists Heidelberg at 32, St. Clements at 20 and St. Jacobs-Elmira at 19 grains per gallon.

The hardness is dissolved calcium and magnesium. When the water is heated, those minerals come out of solution as scale. In a gas tank the burner sits directly under the tank bottom, and that is where the scale settles. The layer insulates the steel from the water above it. The burner then runs longer to heat the same volume, the steel under the scale runs hotter and the glass lining is put under stress. The popping or rumbling you hear while the burner fires is water boiling under the sediment. The sacrificial anode rod, which corrodes so the tank does not, is used up faster as well.

A tankless heater has no tank for scale to settle in. It heats water as it flows through a narrow heat exchanger, and scale coats those passages. Flow drops, the heat exchanger overheats and the unit shows error codes or shuts down under load.

Flushing a tank and descaling a tankless unit

On a tank heater, a flush means draining water from the valve at the base to carry out loose sediment. Hardened scale will not all come out this way. On a tank that has never been flushed, the drain valve can clog, or start to leak once it has been opened. Checking the anode rod at the same time shows how quickly the tank is being consumed.

On a tankless unit, descaling means closing the isolation valves on the hot and cold lines and pumping a descaling solution through the heat exchanger from the service ports. The unit is then flushed with clean water and the inlet screen is cleaned. The manufacturer's manual sets the interval. Keeping to it, with a record of each service, can be a condition of the manufacturer warranty, so keep the receipts.

What a tankless flush costs depends on a few things:

  • whether isolation valves with service ports are already fitted (if they are not, they have to be added first)
  • how hard the water is and how long it has been since the last descale
  • whether the unit is already showing error codes that need diagnosis
  • whether the burner or combustion side has to be opened, which makes it gas work under Ontario Regulation 212/01

The harder your zone, the shorter the interval between flushes. A softener set to the measured hardness of your own zone slows scale in both kinds of heater. A softener set to a default does not do the job as well. See water softeners for how it is sized and set.

How long a water heater lasts, and when to replace it

No single figure applies. Service life depends on the hardness of the water, the tank temperature setting, how much hot water the household uses, and whether the anode and sediment have been looked after. The manufacture date is printed on the rating label or encoded in the serial number. Knowing it puts the other signs in context.

These faults are usually worth repairing:

  • a failed thermocouple, flame sensor or igniter
  • a faulty gas control valve
  • a depleted anode rod, if the tank itself is sound
  • a dripping temperature and pressure relief valve or a leaking drain valve

These signs usually mean replacement:

  • water leaking from the tank body or base, which means the steel has failed and cannot be repaired
  • rusty water from the hot taps only, while the cold runs clear, which points to corrosion inside the tank
  • rumbling that comes back straight after a flush, and hot water that runs out sooner than it used to
  • repeated repairs on an older unit

In the pre-war houses of MacGregor-Albert, Mary Allen and Menno Euclid, rust can also come from original galvanized steel pipe. Run the cold taps before blaming the tank. If cold water is discoloured too, the piping is the more likely cause.

When you do replace, size the new heater to the household rather than to the old label. Confirm the venting, have the outlet temperature measured at the tub against the 49 °C limit, and set a flush or descale interval based on the hardness of your zone. For gas safety around the house, the advice on keeping pipes from freezing covers the main shut-off as well.

Questions to ask before work starts

  • Is the contractor registered with the Technical Standards and Safety Authority for the gas work?
  • Does this job need a building permit from the City?
  • How will the water at the tub be kept to 49 °C, and will it be measured?
  • What hardness zone is the house in, and what flush interval follows from it?
  • Is the price written and itemized, including venting, gas piping and removal of the old unit?

For a replacement, a descale or a tank that has started to leak, see water heaters.

Still have a question?